文章目录[隐藏]

十分钟快速自制CMSIS_DAP仿真器，将ST-LINK-V2变身DAP仿真器！

十分钟快速自制CMSIS_DAP仿真器，将ST-LINK-V2变身DAP仿真器！

（一）简介

说到单片机仿真器(下载器)首先想到的就是J-LINK和ST-LINK，很多人可能还是第一次听说DAP仿真器，那么就先介绍一下。

CMSIS DAP是ARM官方推出的开源仿真器，支持所有的Cortex-A/R/M器件，支持JTAG/SWD接口。有以下特点：

完全开源，没有版权限制，所以相应的价格会很便宜
不需要安装驱动，即插即用
在新版本的DAP里集成了串口，除了下载调试外还能充当USB转串口模块，一机两用
性能方面已经可以满足一般用户的需求

市面上基本所有的离线下载器基本都是基于CMSIS_DAP方案来的，例如正点原子的离线下载器、无线下载器等，还有就是国产单片机厂家做的调试器，例如GD32出的GD-LINK，都是基于CMSIS DAP方案改的。

而ST-LINK是ST官方出的，目前有V1、V2、V3版本，并且闭源，正版的很贵！你买到的很便宜，可能也就十几三十几块钱得样子，这是因为这都是盗版的！网上早就有人把ST-LINK-V2的固件给破解出来的，而且原理图也有，所以市面上的便宜货都是根据官方的原理图做出来的板子，然后下载进固件就完成了一个ST-LINK调试器！但是他们是没有ST-LINK的固件源代码的！

什么是在线调试下载？

在线调试器就是用keil或者iar等软件对目标MCU进行调试和下载程序，适用于开发阶段。像是ST-LINK、J-LINK就是在线调试器。

什么是离线下载？

当项目开发中已经接近尾声或者已经成熟后，那么每生产一块板子就需要刷程序，但是刷程序就需要连接到PC机上通过软件刷，这样的话就非常的麻烦，那么有没有一种方式是做一个小板子，把下载程序的功能集成到这个小板子中，这样的话刷程序就是用这个小板子给目标MCU刷程序，就是手持式的。

有！就是离线下载器！

离线下载器的功能说简单点就是Keil下载程序的功能！

关于本篇

教程持续更新，最终的目的是做一个在线调试+离线下载完整功能的仿真器。

本篇教程就先实现用keil能够在线调试下载程序和调试的功能，这是实现完整功能最简单的一步。

（二）调试器的原理

在教程开始之前，我觉得有必要说一下调试器的原理以及他是怎么工作的，怎么把程序下载到目标MCU的，这里以KEIL+ST-LINK为例进行说明。

我们使用keil下载程序的时候，必须要选定一个下载算法，如下所示：

当你使用STM32的时候必须要安装pack包，而下载算法就在pack包内，安装好后就在keil软件的安装目录下了，具体在这里：

Keil会根据你当前工程使用的芯片，自动去识别应该用哪一个下载算法，例如我目前这个工程是用的STM32F103C8这个芯片，FLASH容量是64K的，属于这个系列的小容量，那么KEIL就自动给我识别了STM32F103x_128.FLM这个下载算法。

那么这个下载算法是什么东西？

进入这个目录后，他有一个工程，而这个工程就是下载算法的模板工程，我们打开看一下：

打开工程后很简单的，就只有两个文件，函数也很简单都是对FLASH的操作，编译一下看看：

AXF（ARM Executable File）是ARM芯片使用的文件格式，它除了包含bin代码外，还包括了输出给调试器的调试信息

看到没！编译完了之后生成了STM32F103x_16.axf文件，然后只是做了一个文件复制并且重命名成了STM32F10x_16.FLM文件！

现在对下载算法就明确了，下载算法其实就是对目标MCU的FLASH的一系列操作函数！

那么KEIL给目标MCU下载程序的时候，其实就是解析出编译好的.axf文件，然后通过USB连接线经过ST-LINK先将下载算法加载进目标MCU的内存中并运行，由于.axf文件中包含的信息很多，其中就有当程序加载进内存后函数在内存中的地址，这个地址也可以通过.map文件查看(.map文件也是keil在编译完工程后生成的)，知道函数在内存中的地址，就可以在外部通过特定的进行调用，所以STLINK就是接收来自KEIL的固件程序，然后操控目标单片机内存中的FLASH的操作函数，在通过SWD协议将固件下载进目标MCU的FLASH中，就这样实现了程序下载，后面我们会做离线下载器那么也就明确了，可以将接收KEIL的下发固件这一个步骤变成本地SD卡存储固件，这样不就实现了离线~

现在keil整个下载程序的流程清楚了后，我们的CMSIS_DAP就可以分成两步骤进行：

第一步：实现KEIL通过USB和DAP的通信
第二步：DAP通过SWD协议将收到固件下载进目标MCU

对于第一步，我们使用STM32CubeMX软件生成工程，然后对源码进行一个简单的修改就可以完成。如果你对USB没有一个充分的了解，本章教程可以先不用管为什么这么修改源代码，跟着步骤来即可，我的另一篇博客有对USB相关知识的扫盲，可以帮助你快速了解：https://blog.csdn.net/qq153471503/article/details/116053851

对于第二步，我们需要移植自ARM官方的CMSIS_DAP源码，源代码在Keil软件的安装目录下，ARM官方的代码是基于LPC单片机的，但是不妨碍我们移植使用：

我们需要的就是上图中这三个文件夹中的源文件以及USBD_User_HID_0.c文件即可，这个文件在这里：

（三）工程配置

紧接上文，现在开始实现第一步，由于我目前手头没有现成的硬件，然后我想起ST-LINK其实也是个STM32F103C8单片机，那么我用STLINK的板子不就行了，而且在网上还能找到原理图，省去了自己做板子验证的步骤，等软件调试完毕后，在做板子把它做得小巧精致些。

它的原理图是这样的：

从原理图上可知，使用的引脚分布如下：

JTAG_nTRST（PB1）
JTAG_nRESET（PB0）
JTAG_TDI（PA7）
JTAG_TMS（PB14，这个引脚也是SWD模式下的SWDIO引脚）
JTAG_TCK（PB13/PA5，这个引脚也是SWD模式下的SWCLK引脚）
JTAG_TDO（PA6/PA10）
LED灯（PA9，低电平为红灯，高电平为绿灯）

对于JTAG_TCK，这是时钟信号引脚，官方用了PB13和PA5两个引脚，我猜测是因为为了提高抗干扰能力，JTAG和SWD两种模式下，使用不同的引脚当做时钟信号。JTAG_TMS引脚同理。

对于JTAG_TDO，当JTAG模式时，这是JTAG的数据输入引脚，当使用SWD模式时，这个引脚可以作为调试输出的作用，所以也是分成了两个引脚来用。

在本教程中，我们就各只用一个IO就可以，不搞那么麻烦。

下面开始贴一下我的配置，时钟配置到72M，并开启USB配置成48M，如下：

下载程序的调试接口配置为SWD模式：

USB的配置如下：

IO引脚的配置如下：

这就是全部的配置内容，然后生成代码就可以了！

（四）移植DAP源码

将DAP加入我们的工程，如下所示：

对于DAP源码的移植，我们主要就是修改DAP_config.h和USBD_User_HID_0.c俩文件，其中DAP_config.h是修改的GPIO以及DAP的一些默认配置参数，USBD_User_HID_0.c就是USB与PC的函数接口了，由于原CMSIS_DAP工程是基于LCP单片机并且跑了系统的，而我没有跑系统，所以就需要将USBD_User_HID_0.c文件中使用系统了的API换成轮训方式即可，下面贴一下我的配置：

DAP_config.h文件：

/*
 * Copyright (c) 2013-2017 ARM Limited. All rights reserved.
 *
 * SPDX-License-Identifier: Apache-2.0
 *
 * Licensed under the Apache License, Version 2.0 (the License); you may
 * not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 * www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an AS IS BASIS, WITHOUT
 * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 *
 * ----------------------------------------------------------------------
 *
 * $Date:        1. December 2017
 * $Revision:    V2.0.0
 *
 * Project:      CMSIS-DAP Configuration
 * Title:        DAP_config.h CMSIS-DAP Configuration File (Template)
 *
 *---------------------------------------------------------------------------*/

#ifndef __DAP_CONFIG_H__
#define __DAP_CONFIG_H__


//**************************************************************************************************
/**
\defgroup DAP_Config_Debug_gr CMSIS-DAP Debug Unit Information
\ingroup DAP_ConfigIO_gr
@{
Provides definitions about the hardware and configuration of the Debug Unit.

This information includes:
 - Definition of Cortex-M processor parameters used in CMSIS-DAP Debug Unit.
 - Debug Unit Identification strings (Vendor, Product, Serial Number).
 - Debug Unit communication packet size.
 - Debug Access Port supported modes and settings (JTAG/SWD and SWO).
 - Optional information about a connected Target Device (for Evaluation Boards).
*/

#include "main.h"

/// Processor Clock of the Cortex-M MCU used in the Debug Unit.
/// This value is used to calculate the SWD/JTAG clock speed.
#define CPU_CLOCK               72000000U       ///< Specifies the CPU Clock in Hz.

/// Number of processor cycles for I/O Port write operations.
/// This value is used to calculate the SWD/JTAG clock speed that is generated with I/O
/// Port write operations in the Debug Unit by a Cortex-M MCU. Most Cortex-M processors
/// require 2 processor cycles for a I/O Port Write operation.  If the Debug Unit uses
/// a Cortex-M0+ processor with high-speed peripheral I/O only 1 processor cycle might be
/// required.
#define IO_PORT_WRITE_CYCLES    2U              ///< I/O Cycles: 2=default, 1=Cortex-M0+ fast I/0.

/// Indicate that Serial Wire Debug (SWD) communication mode is available at the Debug Access Port.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define DAP_SWD                 1               ///< SWD Mode:  1 = available, 0 = not available.

/// Indicate that JTAG communication mode is available at the Debug Port.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define DAP_JTAG                1               ///< JTAG Mode: 1 = available, 0 = not available.

/// Configure maximum number of JTAG devices on the scan chain connected to the Debug Access Port.
/// This setting impacts the RAM requirements of the Debug Unit. Valid range is 1 .. 255.
#define DAP_JTAG_DEV_CNT        8U              ///< Maximum number of JTAG devices on scan chain.

/// Default communication mode on the Debug Access Port.
/// Used for the command \ref DAP_Connect when Port Default mode is selected.
#define DAP_DEFAULT_PORT        1U              ///< Default JTAG/SWJ Port Mode: 1 = SWD, 2 = JTAG.

/// Default communication speed on the Debug Access Port for SWD and JTAG mode.
/// Used to initialize the default SWD/JTAG clock frequency.
/// The command \ref DAP_SWJ_Clock can be used to overwrite this default setting.
#define DAP_DEFAULT_SWJ_CLOCK   10000000U       ///< Default SWD/JTAG clock frequency in Hz.

/// Maximum Package Size for Command and Response data.
/// This configuration settings is used to optimize the communication performance with the
/// debugger and depends on the USB peripheral. Typical vales are 64 for Full-speed USB HID or WinUSB,
/// 1024 for High-speed USB HID and 512 for High-speed USB WinUSB.
#define DAP_PACKET_SIZE         64U             ///< Specifies Packet Size in bytes.

/// Maximum Package Buffers for Command and Response data.
/// This configuration settings is used to optimize the communication performance with the
/// debugger and depends on the USB peripheral. For devices with limited RAM or USB buffer the
/// setting can be reduced (valid range is 1 .. 255).
#define DAP_PACKET_COUNT        8U              ///< Specifies number of packets buffered.

/// Indicate that UART Serial Wire Output (SWO) trace is available.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define SWO_UART                0               ///< SWO UART:  1 = available, 0 = not available.

/// Maximum SWO UART Baudrate.
#define SWO_UART_MAX_BAUDRATE   10000000U       ///< SWO UART Maximum Baudrate in Hz.

/// Indicate that Manchester Serial Wire Output (SWO) trace is available.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define SWO_MANCHESTER          0               ///< SWO Manchester:  1 = available, 0 = not available.

/// SWO Trace Buffer Size.
#define SWO_BUFFER_SIZE         4096U           ///< SWO Trace Buffer Size in bytes (must be 2^n).

/// SWO Streaming Trace.
#define SWO_STREAM              0               ///< SWO Streaming Trace: 1 = available, 0 = not available.

/// Clock frequency of the Test Domain Timer. Timer value is returned with \ref TIMESTAMP_GET.
#define TIMESTAMP_CLOCK         72000000U       ///< Timestamp clock in Hz (0 = timestamps not supported).

/// Debug Unit is connected to fixed Target Device.
/// The Debug Unit may be part of an evaluation board and always connected to a fixed
/// known device.  In this case a Device Vendor and Device Name string is stored which
/// may be used by the debugger or IDE to configure device parameters.
#define TARGET_DEVICE_FIXED     0               ///< Target Device: 1 = known, 0 = unknown;

#if TARGET_DEVICE_FIXED
#define TARGET_DEVICE_VENDOR    "ARM"           ///< String indicating the Silicon Vendor
#define TARGET_DEVICE_NAME      "Cortex-M4"     ///< String indicating the Target Device
#endif

/** Get Vendor ID string.
\param str Pointer to buffer to store the string.
\return String length.
*/
__STATIC_INLINE uint8_t DAP_GetVendorString (char *str)
{
    (void)str;
    return (0U);
}

/** Get Product ID string.
\param str Pointer to buffer to store the string.
\return String length.
*/
__STATIC_INLINE uint8_t DAP_GetProductString (char *str)
{
    (void)str;
    return (0U);
}

/** Get Serial Number string.
\param str Pointer to buffer to store the string.
\return String length.
*/
__STATIC_INLINE uint8_t DAP_GetSerNumString (char *str)
{
    (void)str;
    return (0U);
}

///@}


//**************************************************************************************************
/**
\defgroup DAP_Config_PortIO_gr CMSIS-DAP Hardware I/O Pin Access
\ingroup DAP_ConfigIO_gr
@{

Standard I/O Pins of the CMSIS-DAP Hardware Debug Port support standard JTAG mode
and Serial Wire Debug (SWD) mode. In SWD mode only 2 pins are required to implement the debug
interface of a device. The following I/O Pins are provided:

JTAG I/O Pin                 | SWD I/O Pin          | CMSIS-DAP Hardware pin mode
---------------------------- | -------------------- | ---------------------------------------------
TCK: Test Clock              | SWCLK: Clock         | Output Push/Pull
TMS: Test Mode Select        | SWDIO: Data I/O      | Output Push/Pull; Input (for receiving data)
TDI: Test Data Input         |                      | Output Push/Pull
TDO: Test Data Output        |                      | Input
nTRST: Test Reset (optional) |                      | Output Open Drain with pull-up resistor
nRESET: Device Reset         | nRESET: Device Reset | Output Open Drain with pull-up resistor


DAP Hardware I/O Pin Access Functions
-------------------------------------
The various I/O Pins are accessed by functions that implement the Read, Write, Set, or Clear to
these I/O Pins.

For the SWDIO I/O Pin there are additional functions that are called in SWD I/O mode only.
This functions are provided to achieve faster I/O that is possible with some advanced GPIO
peripherals that can independently write/read a single I/O pin without affecting any other pins
of the same I/O port. The following SWDIO I/O Pin functions are provided:
 - \ref PIN_SWDIO_OUT_ENABLE to enable the output mode from the DAP hardware.
 - \ref PIN_SWDIO_OUT_DISABLE to enable the input mode to the DAP hardware.
 - \ref PIN_SWDIO_IN to read from the SWDIO I/O pin with utmost possible speed.
 - \ref PIN_SWDIO_OUT to write to the SWDIO I/O pin with utmost possible speed.
*/


// Configure DAP I/O pins ------------------------------

/** Setup JTAG I/O pins: TCK, TMS, TDI, TDO, nTRST, and nRESET.
Configures the DAP Hardware I/O pins for JTAG mode:
 - TCK, TMS, TDI, nTRST, nRESET to output mode and set to high level.
 - TDO to input mode.
*/
__STATIC_INLINE void PORT_JTAG_SETUP (void)
{
    GPIO_InitTypeDef GPIO_InitStruct = {0};

	__HAL_RCC_GPIOA_CLK_ENABLE();
	__HAL_RCC_GPIOB_CLK_ENABLE();
    __HAL_RCC_GPIOC_CLK_ENABLE();
    
    HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_SET);

	HAL_GPIO_WritePin(JTAG_TCK_GPIO_Port, JTAG_TCK_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_TMS_GPIO_Port, JTAG_TMS_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_nRESET_GPIO_Port, JTAG_nRESET_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_TDI_GPIO_Port, JTAG_TDI_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_TDO_GPIO_Port, JTAG_TDO_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_nTRST_GPIO_Port, JTAG_nTRST_Pin, GPIO_PIN_SET);

	// LED
    GPIO_InitStruct.Pin = LED_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(LED_GPIO_Port, &GPIO_InitStruct);
	
	// TCK
    GPIO_InitStruct.Pin = JTAG_TCK_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_TCK_GPIO_Port, &GPIO_InitStruct);
	
	// TMS
    GPIO_InitStruct.Pin = JTAG_TMS_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_TMS_GPIO_Port, &GPIO_InitStruct);
	
	// TDI
    GPIO_InitStruct.Pin = JTAG_TDI_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_TDI_GPIO_Port, &GPIO_InitStruct);
	
	// nRESET
    GPIO_InitStruct.Pin = JTAG_nRESET_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_nRESET_GPIO_Port, &GPIO_InitStruct);
	
	// nTRST
    GPIO_InitStruct.Pin = JTAG_nTRST_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_nTRST_GPIO_Port, &GPIO_InitStruct);

	// TDO
    GPIO_InitStruct.Pin = JTAG_TDO_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    HAL_GPIO_Init(JTAG_TDO_GPIO_Port, &GPIO_InitStruct);
}

/** Setup SWD I/O pins: SWCLK, SWDIO, and nRESET.
Configures the DAP Hardware I/O pins for Serial Wire Debug (SWD) mode:
 - SWCLK, SWDIO, nRESET to output mode and set to default high level.
 - TDI, nTRST to HighZ mode (pins are unused in SWD mode).
*/
__STATIC_INLINE void PORT_SWD_SETUP (void)
{
    GPIO_InitTypeDef GPIO_InitStruct = {0};
	
	__HAL_RCC_GPIOA_CLK_ENABLE();
	__HAL_RCC_GPIOB_CLK_ENABLE();
    __HAL_RCC_GPIOC_CLK_ENABLE();
    
    HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_SET);

	HAL_GPIO_WritePin(JTAG_TCK_GPIO_Port, JTAG_TCK_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_TMS_GPIO_Port, JTAG_TMS_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_nRESET_GPIO_Port, JTAG_nRESET_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_TDI_GPIO_Port, JTAG_TDI_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_TDO_GPIO_Port, JTAG_TDO_Pin, GPIO_PIN_SET);
	HAL_GPIO_WritePin(JTAG_nTRST_GPIO_Port, JTAG_nTRST_Pin, GPIO_PIN_SET);

	// LED
    GPIO_InitStruct.Pin = LED_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(LED_GPIO_Port, &GPIO_InitStruct);
	
	// TCK
    GPIO_InitStruct.Pin = JTAG_TCK_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_TCK_GPIO_Port, &GPIO_InitStruct);
	
	// TMS
    GPIO_InitStruct.Pin = JTAG_TMS_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_TMS_GPIO_Port, &GPIO_InitStruct);
	
	// nRESET
    GPIO_InitStruct.Pin = JTAG_nRESET_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_nRESET_GPIO_Port, &GPIO_InitStruct);
	
	// TDI TDO nTRST
	HAL_GPIO_DeInit(JTAG_TDI_GPIO_Port, JTAG_TDI_Pin);
	HAL_GPIO_DeInit(JTAG_TDO_GPIO_Port, JTAG_TDO_Pin);
	HAL_GPIO_DeInit(JTAG_nTRST_GPIO_Port, JTAG_nTRST_Pin);
}

/** Disable JTAG/SWD I/O Pins.
Disables the DAP Hardware I/O pins which configures:
 - TCK/SWCLK, TMS/SWDIO, TDI, TDO, nTRST, nRESET to High-Z mode.
*/
__STATIC_INLINE void PORT_OFF (void)
{
	HAL_GPIO_DeInit(JTAG_TCK_GPIO_Port, JTAG_TCK_Pin);
	HAL_GPIO_DeInit(JTAG_TMS_GPIO_Port, JTAG_TMS_Pin);
	HAL_GPIO_DeInit(JTAG_nRESET_GPIO_Port, JTAG_nRESET_Pin);
	HAL_GPIO_DeInit(JTAG_TDI_GPIO_Port, JTAG_TDI_Pin);
	HAL_GPIO_DeInit(JTAG_TDO_GPIO_Port, JTAG_TDO_Pin);
	HAL_GPIO_DeInit(JTAG_nTRST_GPIO_Port, JTAG_nTRST_Pin);
}


// SWCLK/TCK I/O pin -------------------------------------

/** SWCLK/TCK I/O pin: Get Input.
\return Current status of the SWCLK/TCK DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_SWCLK_TCK_IN (void)
{
    return JTAG_TCK_GPIO_Port->ODR & JTAG_TCK_Pin ? 1 : 0;
}

/** SWCLK/TCK I/O pin: Set Output to High.
Set the SWCLK/TCK DAP hardware I/O pin to high level.
*/
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_SET (void)
{
    JTAG_TCK_GPIO_Port->BSRR = JTAG_TCK_Pin;
}

/** SWCLK/TCK I/O pin: Set Output to Low.
Set the SWCLK/TCK DAP hardware I/O pin to low level.
*/
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_CLR (void)
{
    JTAG_TCK_GPIO_Port->BRR = JTAG_TCK_Pin;
}


// SWDIO/TMS Pin I/O --------------------------------------

/** SWDIO/TMS I/O pin: Get Input.
\return Current status of the SWDIO/TMS DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_TMS_IN (void)
{
    return JTAG_TMS_GPIO_Port->ODR & JTAG_TMS_Pin ? 1 : 0;
}

/** SWDIO/TMS I/O pin: Set Output to High.
Set the SWDIO/TMS DAP hardware I/O pin to high level.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_SET (void)
{
    JTAG_TMS_GPIO_Port->BSRR = JTAG_TMS_Pin;
}

/** SWDIO/TMS I/O pin: Set Output to Low.
Set the SWDIO/TMS DAP hardware I/O pin to low level.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_CLR (void)
{
    JTAG_TMS_GPIO_Port->BRR = JTAG_TMS_Pin;
}

/** SWDIO I/O pin: Get Input (used in SWD mode only).
\return Current status of the SWDIO DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_IN (void)
{
    return JTAG_TMS_GPIO_Port->IDR & JTAG_TMS_Pin ? 1 : 0;
}

/** SWDIO I/O pin: Set Output (used in SWD mode only).
\param bit Output value for the SWDIO DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_OUT (uint32_t bit)
{
    if(bit & 0X01)
    {
        JTAG_TMS_GPIO_Port->BSRR = JTAG_TMS_Pin;
    }
    else
    {
        JTAG_TMS_GPIO_Port->BRR = JTAG_TMS_Pin;
    }
}

/** SWDIO I/O pin: Switch to Output mode (used in SWD mode only).
Configure the SWDIO DAP hardware I/O pin to output mode. This function is
called prior \ref PIN_SWDIO_OUT function calls.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_OUT_ENABLE (void)
{
    GPIO_InitTypeDef GPIO_InitStruct = {0};
    GPIO_InitStruct.Pin = JTAG_TMS_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_TMS_GPIO_Port, &GPIO_InitStruct);
}

/** SWDIO I/O pin: Switch to Input mode (used in SWD mode only).
Configure the SWDIO DAP hardware I/O pin to input mode. This function is
called prior \ref PIN_SWDIO_IN function calls.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_OUT_DISABLE (void)
{
    GPIO_InitTypeDef GPIO_InitStruct = {0};
    GPIO_InitStruct.Pin = JTAG_TMS_Pin;
    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
    GPIO_InitStruct.Pull = GPIO_NOPULL;
    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
    HAL_GPIO_Init(JTAG_TMS_GPIO_Port, &GPIO_InitStruct);
}


// TDI Pin I/O ---------------------------------------------

/** TDI I/O pin: Get Input.
\return Current status of the TDI DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_TDI_IN (void)
{
    return JTAG_TDI_GPIO_Port->ODR & JTAG_TDI_Pin ? 1 : 0;
}

/** TDI I/O pin: Set Output.
\param bit Output value for the TDI DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE void PIN_TDI_OUT (uint32_t bit)
{
    if(bit & 0X01)
    {
        JTAG_TDI_GPIO_Port->BSRR = JTAG_TDI_Pin;
    }
    else
    {
        JTAG_TDI_GPIO_Port->BRR = JTAG_TDI_Pin;
    }
}


// TDO Pin I/O ---------------------------------------------

/** TDO I/O pin: Get Input.
\return Current status of the TDO DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_TDO_IN (void)
{
    return JTAG_TDO_GPIO_Port->IDR & JTAG_TDO_Pin ? 1 : 0;
}


// nTRST Pin I/O -------------------------------------------

/** nTRST I/O pin: Get Input.
\return Current status of the nTRST DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_nTRST_IN (void)
{
    return JTAG_nTRST_GPIO_Port->ODR & JTAG_nTRST_Pin ? 1 : 0;
}

/** nTRST I/O pin: Set Output.
\param bit JTAG TRST Test Reset pin status:
           - 0: issue a JTAG TRST Test Reset.
           - 1: release JTAG TRST Test Reset.
*/
__STATIC_FORCEINLINE void PIN_nTRST_OUT (uint32_t bit)
{
    if(bit & 0X01)
    {
        JTAG_nTRST_GPIO_Port->BSRR = JTAG_nTRST_Pin;
    }
    else
    {
        JTAG_nTRST_GPIO_Port->BRR = JTAG_nTRST_Pin;
    }
}

// nRESET Pin I/O------------------------------------------

/** nRESET I/O pin: Get Input.
\return Current status of the nRESET DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_nRESET_IN (void)
{
    return JTAG_nRESET_GPIO_Port->ODR & JTAG_nRESET_Pin ? 1 : 0;
}

/** nRESET I/O pin: Set Output.
\param bit target device hardware reset pin status:
           - 0: issue a device hardware reset.
           - 1: release device hardware reset.
*/
__STATIC_FORCEINLINE void PIN_nRESET_OUT (uint32_t bit)
{
    if(bit & 0X01)
    {
        JTAG_nRESET_GPIO_Port->BSRR = JTAG_nRESET_Pin;
    }
    else
    {
        JTAG_nRESET_GPIO_Port->BRR = JTAG_nRESET_Pin;
    }
}

///@}


//**************************************************************************************************
/**
\defgroup DAP_Config_LEDs_gr CMSIS-DAP Hardware Status LEDs
\ingroup DAP_ConfigIO_gr
@{

CMSIS-DAP Hardware may provide LEDs that indicate the status of the CMSIS-DAP Debug Unit.

It is recommended to provide the following LEDs for status indication:
 - Connect LED: is active when the DAP hardware is connected to a debugger.
 - Running LED: is active when the debugger has put the target device into running state.
*/

/** Debug Unit: Set status of Connected LED.
\param bit status of the Connect LED.
           - 1: Connect LED ON: debugger is connected to CMSIS-DAP Debug Unit.
           - 0: Connect LED OFF: debugger is not connected to CMSIS-DAP Debug Unit.
*/
__STATIC_INLINE void LED_CONNECTED_OUT (uint32_t bit)
{
    if(bit & 0X01)
    {
        HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_RESET);  // 拉低是亮黄灯
    }
    else
    {
        HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_SET);    // 拉高是亮红灯
    }
}

/** Debug Unit: Set status Target Running LED.
\param bit status of the Target Running LED.
           - 1: Target Running LED ON: program execution in target started.
           - 0: Target Running LED OFF: program execution in target stopped.
*/
__STATIC_INLINE void LED_RUNNING_OUT (uint32_t bit)
{
    if(bit & 0X01)
    {
        HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_RESET);  // 拉低是亮黄灯
    }
    else
    {
        HAL_GPIO_WritePin(LED_GPIO_Port, LED_Pin, GPIO_PIN_SET);    // 拉高是亮红灯
    }
}

///@}


//**************************************************************************************************
/**
\defgroup DAP_Config_Timestamp_gr CMSIS-DAP Timestamp
\ingroup DAP_ConfigIO_gr
@{
Access function for Test Domain Timer.

The value of the Test Domain Timer in the Debug Unit is returned by the function \ref TIMESTAMP_GET. By
default, the DWT timer is used.  The frequency of this timer is configured with \ref TIMESTAMP_CLOCK.

*/

/** Get timestamp of Test Domain Timer.
\return Current timestamp value.
*/
__STATIC_INLINE uint32_t TIMESTAMP_GET (void)
{
    return (DWT->CYCCNT);
}

///@}


//**************************************************************************************************
/**
\defgroup DAP_Config_Initialization_gr CMSIS-DAP Initialization
\ingroup DAP_ConfigIO_gr
@{

CMSIS-DAP Hardware I/O and LED Pins are initialized with the function \ref DAP_SETUP.
*/

/** Setup of the Debug Unit I/O pins and LEDs (called when Debug Unit is initialized).
This function performs the initialization of the CMSIS-DAP Hardware I/O Pins and the
Status LEDs. In detail the operation of Hardware I/O and LED pins are enabled and set:
 - I/O clock system enabled.
 - all I/O pins: input buffer enabled, output pins are set to HighZ mode.
 - for nTRST, nRESET a weak pull-up (if available) is enabled.
 - LED output pins are enabled and LEDs are turned off.
*/
__STATIC_INLINE void DAP_SETUP (void)
{
    PORT_JTAG_SETUP();
}

/** Reset Target Device with custom specific I/O pin or command sequence.
This function allows the optional implementation of a device specific reset sequence.
It is called when the command \ref DAP_ResetTarget and is for example required
when a device needs a time-critical unlock sequence that enables the debug port.
\return 0 = no device specific reset sequence is implemented.\n
        1 = a device specific reset sequence is implemented.
*/
__STATIC_INLINE uint8_t RESET_TARGET (void)
{
    return (1U);             // change to '1' when a device reset sequence is implemented
}

///@}


#endif /* __DAP_CONFIG_H__ */

USBD_User_HID_0.c文件：

/*------------------------------------------------------------------------------
 * MDK Middleware - Component ::USB:Device
 * Copyright (c) 2004-2017 ARM Germany GmbH. All rights reserved.
 *------------------------------------------------------------------------------
 * Name:    USBD_User_HID_0.c
 * Purpose: USB Device Human Interface Device class (HID) User module
 * Rev.:    V6.2.3
 *----------------------------------------------------------------------------*/
/**
 * \addtogroup usbd_hidFunctions
 *
 * USBD_User_HID_0.c implements the application specific functionality of the
 * HID class and is used to receive and send data reports to the USB Host.
 *
 * The implementation must match the configuration file USBD_Config_HID_0.h.
 * The following values in USBD_Config_HID_0.h affect the user code:
 *
 *  - 'Endpoint polling Interval' specifies the frequency of requests
 *    initiated by USB Host for \ref USBD_HIDn_GetReport.
 *
 *  - 'Number of Output Reports' configures the values for \em rid of
 *    \ref USBD_HIDn_SetReport.
 *
 *  - 'Number of Input Reports' configures the values for \em rid of
 *    \ref USBD_HIDn_GetReport and \ref USBD_HID_GetReportTrigger.
 *
 *  - 'Maximum Input Report Size' specifies the maximum value for:
 *       - return of \ref USBD_HIDn_GetReport
 *       - len of \ref USBD_HID_GetReportTrigger.
 *
 *  - 'Maximum Output Report Size' specifies the maximum value for \em len
 *    in \ref USBD_HIDn_SetReport for rtype=HID_REPORT_OUTPUT
 *
 *  - 'Maximum Feature Report Size' specifies the maximum value for \em len
 *    in \ref USBD_HIDn_SetReport for rtype=HID_REPORT_FEATURE
 *
 */


//! [code_USBD_User_HID]

#include <stdint.h>
#include <string.h>
#include <stdbool.h>
#include "DAP_config.h"
#include "DAP.h"
#include "usbd_custom_hid_if.h"

#define HID_REPORT_INPUT            0x81
#define HID_REPORT_OUTPUT           0x91
#define HID_REPORT_FEATURE          0xB1

#define USBD_HID_REQ_EP_CTRL        0x01
#define USBD_HID_REQ_PERIOD_UPDATE  0x02
#define USBD_HID_REQ_EP_INT         0x03

static volatile uint16_t USB_RequestIndexI;     // Request  Index In
static volatile uint16_t USB_RequestIndexO;     // Request  Index Out
static volatile uint16_t USB_RequestCountI;     // Request  Count In
static volatile uint16_t USB_RequestCountO;     // Request  Count Out

static volatile uint16_t USB_ResponseIndexI;    // Response Index In
static volatile uint16_t USB_ResponseIndexO;    // Response Index Out
static volatile uint16_t USB_ResponseCountI;    // Response Count In
static volatile uint16_t USB_ResponseCountO;    // Response Count Out
static volatile uint8_t  USB_ResponseIdle;      // Response Idle  Flag
static volatile uint32_t USB_EventFlags;

static uint8_t  USB_Request [DAP_PACKET_COUNT][DAP_PACKET_SIZE];  // Request  Buffer
static uint8_t  USB_Response[DAP_PACKET_COUNT][DAP_PACKET_SIZE];  // Response Buffer

extern USBD_HandleTypeDef hUsbDeviceFS;

// Called during USBD_Initialize to initialize the USB HID class instance.
void USBD_HID0_Initialize (void)
{
    // Initialize variables
    USB_RequestIndexI  = 0U;
    USB_RequestIndexO  = 0U;
    USB_RequestCountI  = 0U;
    USB_RequestCountO  = 0U;
    USB_ResponseIndexI = 0U;
    USB_ResponseIndexO = 0U;
    USB_ResponseCountI = 0U;
    USB_ResponseCountO = 0U;
    USB_ResponseIdle   = 1U;
    USB_EventFlags     = 0U;
}


// Called during USBD_Uninitialize to de-initialize the USB HID class instance.
void USBD_HID0_Uninitialize (void)
{
}

// \brief Prepare HID Report data to send.
// \param[in]   rtype   report type:
//                - HID_REPORT_INPUT           = input report requested
//                - HID_REPORT_FEATURE         = feature report requested
// \param[in]   req     request type:
//                - USBD_HID_REQ_EP_CTRL       = control endpoint request
//                - USBD_HID_REQ_PERIOD_UPDATE = idle period expiration request
//                - USBD_HID_REQ_EP_INT        = previously sent report on interrupt endpoint request
// \param[in]   rid     report ID (0 if only one report exists).
// \param[out]  buf     buffer containing report data to send.
// \return              number of report data bytes prepared to send or invalid report requested.
//              - value >= 0: number of report data bytes prepared to send
//              - value = -1: invalid report requested
int32_t USBD_HID0_GetReport (uint8_t rtype, uint8_t req, uint8_t rid, uint8_t *buf)
{
    (void)rid;

    switch (rtype)
    {
    case HID_REPORT_INPUT:
        switch (req)
        {
        case USBD_HID_REQ_EP_CTRL:        // Explicit USB Host request via Control OUT Endpoint
        case USBD_HID_REQ_PERIOD_UPDATE:  // Periodic USB Host request via Interrupt OUT Endpoint
            break;
        case USBD_HID_REQ_EP_INT:         // Called after USBD_HID_GetReportTrigger to signal data obtained.
            if (USB_ResponseCountI != USB_ResponseCountO)
            {
                // Load data from response buffer to be sent back
                memcpy(buf, USB_Response[USB_ResponseIndexO], DAP_PACKET_SIZE);
                USB_ResponseIndexO++;
                if (USB_ResponseIndexO == DAP_PACKET_COUNT)
                {
                    USB_ResponseIndexO = 0U;
                }
                USB_ResponseCountO++;
                return ((int32_t)DAP_PACKET_SIZE);
            }
            else
            {
                USB_ResponseIdle = 1U;
            }
            break;
        }
        break;
    case HID_REPORT_FEATURE:
        break;
    }
    return (0);
}


// \brief Process received HID Report data.
// \param[in]   rtype   report type:
//                - HID_REPORT_OUTPUT    = output report received
//                - HID_REPORT_FEATURE   = feature report received
// \param[in]   req     request type:
//                - USBD_HID_REQ_EP_CTRL = report received on control endpoint
//                - USBD_HID_REQ_EP_INT  = report received on interrupt endpoint
// \param[in]   rid     report ID (0 if only one report exists).
// \param[in]   buf     buffer that receives report data.
// \param[in]   len     length of received report data.
// \return      true    received report data processed.
// \return      false   received report data not processed or request not supported.
bool USBD_HID0_SetReport (uint8_t rtype, uint8_t req, uint8_t rid, const uint8_t *buf, int32_t len)
{
    (void)req;
    (void)rid;

    switch (rtype)
    {
    case HID_REPORT_OUTPUT:
        if (len == 0)
        {
            break;
        }
        if (buf[0] == ID_DAP_TransferAbort)
        {
            DAP_TransferAbort = 1U;
            break;
        }
        if ((uint16_t)(USB_RequestCountI - USB_RequestCountO) == DAP_PACKET_COUNT)
        {
            USB_EventFlags |= 0X80;
            break;  // Discard packet when buffer is full
        }
        // Store received data into request buffer
        memcpy(USB_Request[USB_RequestIndexI], buf, (uint32_t)len);
        USB_RequestIndexI++;
        if (USB_RequestIndexI == DAP_PACKET_COUNT)
        {
            USB_RequestIndexI = 0U;
        }
        USB_RequestCountI++;
        USB_EventFlags |= 0X01;
        break;
    case HID_REPORT_FEATURE:
        break;
    }
    return true;
}

void USBD_HID0_OutEvent_FS(void)
{
    USBD_CUSTOM_HID_HandleTypeDef *hhid = (USBD_CUSTOM_HID_HandleTypeDef *)hUsbDeviceFS.pClassData;
    USBD_HID0_SetReport(HID_REPORT_OUTPUT, 0, 0, hhid->Report_buf, USBD_CUSTOMHID_OUTREPORT_BUF_SIZE);
}

void USBD_HID0_InEvent_FS(void)
{
    int32_t len;
    USBD_CUSTOM_HID_HandleTypeDef *hhid = (USBD_CUSTOM_HID_HandleTypeDef *)hUsbDeviceFS.pClassData;
    if ((len=USBD_HID0_GetReport(HID_REPORT_INPUT, USBD_HID_REQ_EP_INT, 0, hhid->Report_buf)) > 0)
    {
        USBD_HID_GetReportTrigger(0, 0, hhid->Report_buf, len);
    }
}

// DAP Thread.
__NO_RETURN void DAP_Thread (void *argument)
{
    uint32_t n;
    uint32_t flags = 0;
    (void)argument;

    for (;;)
    {
        while((USB_EventFlags & 0X81) == 0)
        {
            ;
        }
        USB_EventFlags &= (~0X81);

        // Process pending requests
        while (USB_RequestCountI != USB_RequestCountO)
        {
            // Handle Queue Commands
            n = USB_RequestIndexO;
            while (USB_Request[n][0] == ID_DAP_QueueCommands)
            {
                USB_Request[n][0] = ID_DAP_ExecuteCommands;
                n++;
                if (n == DAP_PACKET_COUNT)
                {
                    n = 0U;
                }
                if (n == USB_RequestIndexI)
                {
                    while((USB_EventFlags & 0X81) == 0)
                    {
                        ;
                    }
                    flags = USB_EventFlags;
                    USB_EventFlags &= (~0X81);
                    if(flags & 0X80)
                    {
                        break;
                    }
                }
            }

            // Execute DAP Command (process request and prepare response)
            DAP_ExecuteCommand(USB_Request[USB_RequestIndexO], USB_Response[USB_ResponseIndexI]);

            // Update Request Index and Count
            USB_RequestIndexO++;
            if (USB_RequestIndexO == DAP_PACKET_COUNT)
            {
                USB_RequestIndexO = 0U;
            }
            USB_RequestCountO++;

            // Update Response Index and Count
            USB_ResponseIndexI++;
            if (USB_ResponseIndexI == DAP_PACKET_COUNT)
            {
                USB_ResponseIndexI = 0U;
            }
            USB_ResponseCountI++;

            if (USB_ResponseIdle)
            {
                if (USB_ResponseCountI != USB_ResponseCountO)
                {
                    // Load data from response buffer to be sent back
                    n = USB_ResponseIndexO++;
                    if (USB_ResponseIndexO == DAP_PACKET_COUNT)
                    {
                        USB_ResponseIndexO = 0U;
                    }
                    USB_ResponseCountO++;
                    USB_ResponseIdle = 0U;
                    USBD_HID_GetReportTrigger(0U, 0U, USB_Response[n], DAP_PACKET_SIZE);
                }
            }
        }
    }
}

//! [code_USBD_User_HID]

现在其实就是完成了第二步，DAP通过SWD协议将固件下载进目标单片机FLASH中的步骤，那么下面就开始修改USB的配置，KEIL能通过USB和DAP通信。

修改usbd_custom_hid_if.c文件，找到CUSTOM_HID_ReportDesc_FS数组，改为：

/** Usb HID report descriptor. */
__ALIGN_BEGIN static uint8_t CUSTOM_HID_ReportDesc_FS[USBD_CUSTOM_HID_REPORT_DESC_SIZE] __ALIGN_END =
{
  /* USER CODE BEGIN 0 */
  0x06,0x00,0xFF,         /*  Usage Page (vendor defined) ($FF00) global */
  0x09,0x01,              /*  Usage (vendor defined) ($01) local */
  0xA1,0x01,              /*  Collection (Application) */
  0x15,0x00,              /*   LOGICAL_MINIMUM (0) */
  0x25,0xFF,              /*   LOGICAL_MAXIMUM (255) */
  0x75,0x08,              /*   REPORT_SIZE (8bit) */
 
  // Input Report
  0x95,64,                /*   Report Length (64 REPORT_SIZE) */
  0x09,0x01,              /*   USAGE (Vendor Usage 1) */
  0x81,0x02,              /*   Input(data,var,absolute) */
 
  // Output Report
  0x95,64,                /*   Report Length (64 REPORT_SIZE) */
  0x09,0x01,              /*   USAGE (Vendor Usage 1) */
  0x91,0x02,              /*   Output(data,var,absolute) */
 
  // Feature Report
  0x95,64,                /*   Report Length (64 REPORT_SIZE) */
  0x09,0x01,              /*   USAGE (Vendor Usage 1) */
  0xB1,0x02,              /*   Feature(data,var,absolute) */
  /* USER CODE END 0 */
  0xC0                    /*  END_COLLECTION	             */
};

导入USBD_User_HID_0.c文件中的这四个函数，并新写一个CUSTOM_HID_InEvent_FS函数：

修改以下几个函数添加调用：

修改usbd_custom_hid_if.h文件，导出新增的USBD_HID_GetReportTrigger这个函数声明：

然后修改usbd_customhid.h文件的这几个宏：

然后在改一下USBD_CUSTOM_HID_ItfTypeDef这个结构，需要新增一个函数指针：

然后修改main.c文件，添加头文件包含：

main函数内容如下：

至此，就已经完成了一个CMSIS_DAP仿真器！

下载编译工程，将程序下载进STLINK的板子中去试试吧！

注：STLINK可能设置了写保护，需要先解除写保护才能用KEIL给它下载程序，解除办法见我的另一篇博客：STM32下载程序问题解决：Can not read memory! Disable Read Out Proyection and try.

（五）测试CMSIS_DAP仿真器

将程序下载进板子后，USB插入电脑，设备管理器->人体学输入设备会多出一个USB输入设备和符合HID标准的供应商定义设备，如下图：

然后我们打开KEIL，调试器选择CMSIS_DAP：

给目标板下载程序：

没问题！再试试在线调试：

也没问题！成功！

（六）补充内容：软启动的实现

通过以上教程后，此时的DAP仿真器已经能够正常使用了，但是还是有缺陷的，就是无法像ST-LINK那样通过软件复位的形式运行程序，换句话说就是用keil下载程序后是不运行的，必须手动复位一下，或者必须将目标单片机的复位引脚接到DAP的复位控制引脚上，我们最初的设计目的就是四脚的DAP，而不是5脚的(5脚是多了一个硬件RESET)，所以下面就需要修改一下SWD的源码，在对下载目标MCU下载完程序后，使用软件复位的形式给他复位一下。

这一部分内容牵扯到离线下载器的源码内容，离线下载器中的源码主要是移植自ARM官方的DAP-LINK中的源码，我们现在还未实现离线下载的功能，所以只需要SWD_host.c文件，这个文件实现的是怎么通过SWD协议控制目标MCU的功能。

需要修改的是DAP.c文件中的函数DAP_ProcessCommand：

if(DAP_Data.debug_port == DAP_PORT_SWD)  /* +++lakun:SWD模式下需要软启动，JTAG模式下不需要 */
{
	swd_init_debug();                    /* +++lakun:使目标MCU进入调试模式 */
	swd_set_target_reset(0);             /* +++lakun:写入命令实现软复位启动 */
}