AMG8833介绍

内部框图

可以看到AMG8833的内部有红外点阵测温，并且还带有一个热敏电阻。使用同一个ADC进行采样，然后送给Control。

器件参数

测温点数：64（8x8的矩阵）

帧率：10帧每秒或1帧每秒

红外测温分辨率：0.25℃

热敏电阻测量温度范围：-20℃~80℃

热敏电阻分辨率：0.0625℃

红外测温的准确度：High gain误差在2.5℃以内；Low gain误差在3℃以内。

点阵的排布顺序

从右到左、从下到上。因此右下角才是第一个点。

原理图

2脚和3脚是IIC通信引脚，最大速度400K。

4脚是中断引脚，如果INT control寄存器中激活了中断功能，当发生中断，此引脚会拉低。

5脚是IIC设备地址选择脚。拉低，设备地址为110 1000，即0x68。拉高，设备地址为110 1001，即0x69。

设备地址占据高7位，最低位是读写位，0表示写，1表示读。所以当5脚拉低，进行写操作时，8位数据为：1101 0000，即0xD0，读操作时，8位数据为：1101 0001，即0xD1。

6脚为地。

9脚和13脚为VDD，可以3.3V或5V供电。

10脚接一个电容和电阻。

12脚接一个电容。

内部寄存器

1、Power Control寄存器：

设置AMG8833的工作模式

2、Reset寄存器：

进行软复位。

有两种复位方式：

Flag Reset会清除Status寄存器（0x04）、中断标志、中断表（0x10～0x17）

Initial Reset会复位标志，并使AMG8833的参数恢复初始。

3、Frame Rate寄存器：设定帧率

bit0: Setting Frame Mode
1: 1FPS
0: 10FPS

4、Interrupt Control寄存器：

配置中断功能

bit1: INTMOD
1: Absolute Value Interrupt Mode
0: Difference Interrupt Mode
bit0: INTEN
1: INT 引脚输出使能
0: INT 引脚禁止输出（保持高阻状态）

5、Status寄存器：

溢出标志和中断标志

bit3: OVF_THS
1: 热敏电阻温度输出溢出标志
（Value of Thermistor (0x0E、0x0F) : 0xFFF）
bit2: OVF_IRS
1: 红外温度输出溢出标志
（Value of Temperature Register（0x80～0xFF）: 0xFFF）
bit1: INTF
1: 发生中断标志
（Value of Interrupt Table Register（0x10～0x17）: Except for 0x00）

6、Status Clear寄存器：

清除溢出标志和中断标志
bit3: OVT_CLR
1: 清除热敏电阻温度输出溢出标志
bit2: OVS_CLR
1: 清除红外温度输出溢出标志
bit1: INTCLR
1: 清除中断标志

7、Average寄存器：

设置移动平均输出模式
bit5: MAMOD
1:：Twice moving average Output Mode

0：No moving average

8、Interrupt Level寄存器：

设置发生中断的上限值、下限值、迟滞值。

INT_LVL_H [11:0]:中断上限值，当温度高于此值，输出中断并且设置Interrupt Table寄存器。

INT_LVL_L [11:0]:中断下限值，当温度低于此值，输出中断并且设置Interrupt Table寄存器。

INT_HYS [11:0]:设置上限值、下限值的迟滞值，类似于施密特触发器。

上述3个数据都是12位数据。最高位为符号位，值为0表示正，值为1表示负。步进值为0.25℃。

9、Thermistor寄存器：

热敏电阻测量的温度值

有12位数据。最高位为符号位，值为0表示正，值为1表示负。步进值为0.0625℃。举例如下：

10、Interrupt Table寄存器：

显示哪一个像素点发生了中断

当64个像素点中的某一个点的温度值高于或低于了Interrupt Level寄存器中设置的上下限，就会在Interrupt Table寄存器的对应位设置值。值为1代表发生了中断，0表示没有。

11、Temperature寄存器：

红外点阵测量的温度值

有12位数据。最高位为符号位，值为0表示正，值为1表示负。步进值为0.25℃。举例如下：

0x80和0x81保存的是第一个像素的温度值，1-64像素对应地址为0x80~0xFF。

注：

（1）1 - 64像素（0x80~0xFF）的温度值是一起更新的，不需要任何指令。

（2）0x80~0xFF的数据是一次读出的，所以不用担心新的温度值和旧的温度值会混在一起。

HI3516驱动开发

为了避免麻烦，并且这里的传输数据量并不是非常大，所以直接用IO读取数据
所以如果要用其他LINUX开发板底层函数必须根据你们的板子重新编写。

/*
 * @Description: 
 * @Autor: YURI
 * @Date: 2022-01-21 17:14:06
 * @LastEditors: YURI
 * @LastEditTime: 2022-01-31 00:03:07
 */
#ifndef amg8833_H
#define amg8833_H

#define GPIO0_BASE_ADDR          	0x120D0000
#define GPIO0_DIR_ADDR            ((GPIO0_BASE_ADDR) + (0x400))
#define GPIO0_DATA_OUT_ADDR       ((GPIO0_BASE_ADDR) + (0x000))
#define GPIO0_DATA                ((GPIO0_BASE_ADDR) + (0x3FC))

#define GPIO1_BASE_ADDR          	0x120D1000
#define GPIO1_DIR_ADDR            ((GPIO1_BASE_ADDR) + (0x400))
#define GPIO1_DATA_OUT_ADDR       ((GPIO1_BASE_ADDR) + (0x000))
#define GPIO1_DATA                ((GPIO1_BASE_ADDR) + (0x3FC))

#define GPIO2_BASE_ADDR          	0x120D2000
#define GPIO2_DIR_ADDR            ((GPIO2_BASE_ADDR) + (0x400))
#define GPIO2_DATA_OUT_ADDR       ((GPIO2_BASE_ADDR) + (0x000))
#define GPIO2_DATA                ((GPIO2_BASE_ADDR) + (0x3FC))

#define GPIO3_BASE_ADDR          	0x120D3000
#define GPIO3_DIR_ADDR            ((GPIO3_BASE_ADDR) + (0x400))
#define GPIO3_DATA_OUT_ADDR       ((GPIO3_BASE_ADDR) + (0x000))
#define GPIO3_DATA                ((GPIO3_BASE_ADDR) + (0x3FC))

#define GPIO4_BASE_ADDR          	0x120D4000
#define GPIO4_DIR_ADDR            ((GPIO4_BASE_ADDR) + (0x400))
#define GPIO4_DATA_OUT_ADDR       ((GPIO4_BASE_ADDR) + (0x000))
#define GPIO4_DATA                ((GPIO4_BASE_ADDR) + (0x3FC))

#define GPIO5_BASE_ADDR          	0x120D5000
#define GPIO5_DIR_ADDR            ((GPIO5_BASE_ADDR) + (0x400))
#define GPIO5_DATA_OUT_ADDR       ((GPIO5_BASE_ADDR) + (0x000))
#define GPIO5_DATA                ((GPIO5_BASE_ADDR) + (0x3FC))

#define GPIO6_BASE_ADDR          	0x120D6000
#define GPIO6_DIR_ADDR            ((GPIO6_BASE_ADDR) + (0x400))
#define GPIO6_DATA_OUT_ADDR       ((GPIO6_BASE_ADDR) + (0x000))
#define GPIO6_DATA                ((GPIO6_BASE_ADDR) + (0x3FC))

#define GPIO7_BASE_ADDR          	0x120D7000
#define GPIO7_DIR_ADDR            ((GPIO7_BASE_ADDR) + (0x400))
#define GPIO7_DATA_OUT_ADDR       ((GPIO7_BASE_ADDR) + (0x000))
#define GPIO7_DATA                ((GPIO7_BASE_ADDR) + (0x3FC))

#define GPIO8_BASE_ADDR          	0x120D8000
#define GPIO8_DIR_ADDR            ((GPIO8_BASE_ADDR) + (0x400))
#define GPIO8_DATA_OUT_ADDR       ((GPIO8_BASE_ADDR) + (0x000))
#define GPIO8_DATA                ((GPIO8_BASE_ADDR) + (0x3FC))

#define GPIO9_BASE_ADDR          	0x120D9000
#define GPIO9_DATA_OUT_ADDR       ((GPIO9_BASE_ADDR) + (0x000))
#define GPIO9_SET_DATA_ADDR       ((GPIO9_DATA_OUT_ADDR) + (0x200))
#define GPIO9_DATA                ((GPIO9_BASE_ADDR) + (0x3FC))

#define GPIO10_BASE_ADDR          	0x120DA000
#define GPIO10_DIR_ADDR            ((GPIO10_BASE_ADDR) + (0x400))
#define GPIO10_DATA_OUT_ADDR       ((GPIO10_BASE_ADDR) + (0x000))
#define GPIO10_DATA                ((GPIO10_BASE_ADDR) + (0x3FC))

#define GPIO11_BASE_ADDR          	0x120DB000
#define GPIO11_DIR_ADDR            ((GPIO11_BASE_ADDR) + (0x400))
#define GPIO11_DATA_OUT_ADDR       ((GPIO11_BASE_ADDR) + (0x000))
#define GPIO11_DATA                ((GPIO11_BASE_ADDR) + (0x3FC)) 
enum amg8833_pin_direction{amg8833_IN=0,amg8833_OUT=1};

#define AMG8833_DELAY_TIME  4

//amg8833 关键控制器
typedef struct 
{
    volatile unsigned long *pin_mutx;   //管脚选择地址
    volatile unsigned long *pin_dir;    //管脚方向地址
    volatile unsigned long *pin_data;//控制管脚的数据组在的位置
    volatile int pin_index;             //管脚号
}amg8833_pin;

//amg8833 硬件控制器
typedef struct 
{
    amg8833_pin *sck;        // 时钟
    amg8833_pin *sda;        // 数据线
    amg8833_pin *inter;      // 中断线
    amg8833_pin *ad0;        // 地址选择
}amg8833_ctl;


#define AMG88xx_PIXEL_TEMP_CONVERSION 0.25
#define AMG88xx_THERMISTOR_CONVERSION 0.0625
enum
{
	AMG88xx_PCTL = 0x00,
	AMG88xx_RST = 0x01,
	AMG88xx_FPSC = 0x02,
	AMG88xx_INTC = 0x03,
	AMG88xx_STAT = 0x04,
	AMG88xx_SCLR = 0x05,
	//0x06 reserved
	AMG88xx_AVE = 0x07,
	AMG88xx_INTHL = 0x08,
	AMG88xx_INTHH = 0x09,
	AMG88xx_INTLL = 0x0A,
	AMG88xx_INTLH = 0x0B,
	AMG88xx_IHYSL = 0x0C,
	AMG88xx_IHYSH = 0x0D,
	AMG88xx_TTHL = 0x0E,
	AMG88xx_TTHH = 0x0F,
	AMG88xx_INT_OFFSET = 0x010,
	AMG88xx_PIXEL_OFFSET = 0x80
};
enum power_modes{
	AMG88xx_NORMAL_MODE = 0x00,
	AMG88xx_SLEEP_MODE = 0x01,
	AMG88xx_STAND_BY_60 = 0x20,
	AMG88xx_STAND_BY_10 = 0x21
};
enum sw_resets {
	AMG88xx_FLAG_RESET = 0x30,
	AMG88xx_INITIAL_RESET = 0x3F
};
enum frame_rates {
	AMG88xx_FPS_10 = 0x00,
	AMG88xx_FPS_1 = 0x01
};
enum int_enables{
	AMG88xx_INT_DISABLED = 0x00,
	AMG88xx_INT_ENABLED = 0x01
};
enum int_modes {
	AMG88xx_DIFFERENCE = 0x00,
	AMG88xx_ABSOLUTE_VALUE = 0x01
};
#define AMG88xx_ADR    0xD0          //5脚拉低时的设备地址
 
#endif

/*
 * @Description: 
 * @Autor: YURI
 * @Date: 2022-01-30 17:18:51
 * @LastEditors: YURI
 * @LastEditTime: 2022-01-31 00:33:38
 */
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/fs.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <asm/uaccess.h>
#include <asm/irq.h>
#include <linux/slab.h> 
#include <asm/io.h>
#include <linux/delay.h>
#include "amg8833.h"
amg8833_ctl amg8833;
#define DEVICE_NAME "amg8833" 

/**
 * @description: amg8833 管脚初始化
 * @param {unsigned long} base_addr
 * @param {unsigned long} mutex_addr
 * @param {int} mutex_select
 * @param {int} pin_direction
 * @param {int} pinindex
 * @param {int} pindefaultvalue
 * @return {*}
 * @author: YURI
 */
static amg8833_pin* amg8833_pin_init(unsigned long base_addr,unsigned long mutex_addr,int mutex_select,int pin_direction,int pinindex,int pindefaultvalue)
{
    amg8833_pin* pin=(amg8833_pin*)kmalloc(sizeof(amg8833_pin),GFP_KERNEL);
    pin->pin_dir     = (volatile unsigned long *)ioremap(base_addr+(0x400), 32);//方向选择寄存器
    pin->pin_data    = (volatile unsigned long *)ioremap(base_addr+(0x3FC), 32);//数据寄存器
    pin->pin_mutx    = (volatile unsigned long *)ioremap(mutex_addr, 32);       //功能选择寄存器
    
    pin->pin_index   = pinindex;
    *(pin->pin_data)|=(pindefaultvalue<<pinindex);
    *(pin->pin_mutx)=mutex_select;
    *(pin->pin_dir )=(pin_direction<<pinindex);
    return pin;
} 
/**
 * @description: amg8833 管脚恢复
 * @param {amg8833_pin*} pin
 * @return {*}
 * @author: YURI
 */
static void amg8833_pin_uninit(amg8833_pin* pin)
{
    iounmap(pin->pin_data);
    iounmap(pin->pin_mutx);
    iounmap(pin->pin_dir);
    kfree(pin);
}
/**
 * @description: 改变输入输出方向
 * @param {amg8833_pin*} pin
 * @param {int} pin_direction
 * @return {*}
 * @author: YURI
 */
static inline void amg8833_pin_change_direction(amg8833_pin* pin,int pin_direction)
{
    *(pin->pin_dir )=(pin_direction<<pin->pin_index);
}
/**
 * @description: 设置管脚数值
 * @param {amg8833_pin*} pin
 * @param {int} value
 * @return {*}
 * @author: YURI
 */
static inline void amg8833_pin_change_value(amg8833_pin* pin,int value)
{
    //printk("KERNEL VALUE %d",value);
   if(value) *(pin->pin_data)|=(1<<(pin->pin_index));
   else *(pin->pin_data)&=~(1<<(pin->pin_index));
}
/**
 * @description: 反转管脚
 * @param {amg8833_pin*} pin
 * @return {*}
 * @author: YURI
 */
static inline void amg8833_pin_toggle_value(amg8833_pin* pin)
{
   if(*(pin->pin_data)&(1<<(pin->pin_index))) *(pin->pin_data)&=~(1<<(pin->pin_index));
   else *(pin->pin_data)|=(1<<(pin->pin_index));
}
/**
 * @description: 获取管脚电平
 * @param {amg8833_pin*} pin
 * @return {*}
 * @author: YURI
 */
static inline int amg8833_pin_get_value(amg8833_pin* pin)
{
    if(*(pin->pin_data)&(1<<(pin->pin_index)))return 1;
    else return 0;
}
/**
 * @description: amg8833结构体初始化，初始化所有管脚
 * @param {*}
 * @return {*}
 * @author: YURI
 */
static void amg8833_ctl_init(void)
{
    amg8833.sck   =amg8833_pin_init(GPIO0_BASE_ADDR,0X112F0034,0X520,amg8833_OUT,6,0);//0_6
    amg8833.sda   =amg8833_pin_init(GPIO2_BASE_ADDR,0X114F0068,0X520,amg8833_OUT,3,0);//2_3
    amg8833.inter =amg8833_pin_init(GPIO8_BASE_ADDR,0X112F0040,0X524,amg8833_OUT,7,0);//8_7
    amg8833.ad0   =amg8833_pin_init(GPIO7_BASE_ADDR,0X112F0044,0X520,amg8833_OUT,0,0);//7_0
}
/**
 * @description: 释放硬件资源
 * @param {*}
 * @return {*}
 * @author: YURI
 */
static void amg8833_ctl_uninit(void)
{
    amg8833_pin_uninit(amg8833.sck);
    amg8833_pin_uninit(amg8833.sda);
    amg8833_pin_uninit(amg8833.inter);
    amg8833_pin_uninit(amg8833.ad0);
}

/**
 * @description:IIC开始信号 当SLK高电平 SDA由高变低
 * @param {*}
 * @return {*}
 * @author: YURI
 */
void amg_iic_start(void)
{
    amg8833_pin_change_direction(amg8833.sda,amg8833_OUT);
    amg8833_pin_change_value(amg8833.sda,1);
    amg8833_pin_change_value(amg8833.sck,1);
    udelay(AMG8833_DELAY_TIME);
    amg8833_pin_change_value(amg8833.sda,0);
    udelay(AMG8833_DELAY_TIME);
    amg8833_pin_change_value(amg8833.sck,0);
}

/**
 * @description:IIC结束信号 当SLK高电平 SDA由低变高
 * @param {*}
 * @return {*}
 * @author: YURI
 */
void amg_iic_stop(void)
{
    amg8833_pin_change_direction(amg8833.sda,amg8833_OUT);
    amg8833_pin_change_value(amg8833.sck,0);
    amg8833_pin_change_value(amg8833.sda,0);
    udelay(AMG8833_DELAY_TIME);
    amg8833_pin_change_value(amg8833.sck,1);
    amg8833_pin_change_value(amg8833.sda,1);
    udelay(AMG8833_DELAY_TIME);
}
/**
 * @description: 主机SCL拉高，读取从机SDA的电平，为低电平表示产生应答
 * @param {*}
 * @return {*}
 * @author: YURI
 */
unsigned char amg_iic_wait_ack(void)
{
    unsigned char ucErrTime=0;
    amg8833_pin_change_direction(amg8833.sda,amg8833_IN);
    amg8833_pin_change_value(amg8833.sda,1);udelay(AMG8833_DELAY_TIME);
    amg8833_pin_change_value(amg8833.sck,1);udelay(AMG8833_DELAY_TIME);
   	while(amg8833_pin_get_value(amg8833.sda))
	{
		ucErrTime++;
		if(ucErrTime>250)
		{
			amg_iic_stop();
			return 1;
		}
	}
	amg8833_pin_change_value(amg8833.sck,0);//时钟输出0 	   
	return 0;   
}

//产生ACK应答
//1.先拉低SCL，再拉低SDA
//2.拉高SCL
//3.拉低SCL
void amg_iic_ack(void)
{
    amg8833_pin_change_value(amg8833.sck,0);
    amg8833_pin_change_direction(amg8833.sda,amg8833_OUT);
    amg8833_pin_change_value(amg8833.sda,0);
	udelay(AMG8833_DELAY_TIME/2);
	amg8833_pin_change_value(amg8833.sck,1);
	udelay(AMG8833_DELAY_TIME/2);
	amg8833_pin_change_value(amg8833.sck,0);
}
 
//不产生ACK应答	
//1.先拉低SCL，再拉高SDA
//2.拉高SCL
//3.拉低SCL	    
void amg_iic_nack(void)
{
    amg8833_pin_change_value(amg8833.sck,0);
    amg8833_pin_change_direction(amg8833.sda,amg8833_OUT);
    amg8833_pin_change_value(amg8833.sda,1);
	udelay(AMG8833_DELAY_TIME/2);
	amg8833_pin_change_value(amg8833.sck,1);
	udelay(AMG8833_DELAY_TIME/2);
	amg8833_pin_change_value(amg8833.sck,0);
}

//IIC发送一个字节
//返回从机有无应答
//1，有应答
//0，无应答			  
void amg_iic_send_byte(unsigned char txd)
{                        
    unsigned char t;   
	amg8833_pin_change_direction(amg8833.sda,amg8833_OUT);   
    amg8833_pin_change_value(amg8833.sck,0);//拉低时钟开始数据传输
    for(t=0;t<8;t++)
    {              
		if((txd&0x80)>>7)
			amg8833_pin_change_value(amg8833.sda,1);
		else
			amg8833_pin_change_value(amg8833.sda,0);
		txd<<=1; 	  
		udelay(AMG8833_DELAY_TIME/2);  
		amg8833_pin_change_value(amg8833.sck,1);
		udelay(AMG8833_DELAY_TIME/2); 
		amg8833_pin_change_value(amg8833.sck,0);	
		udelay(AMG8833_DELAY_TIME/2);
    }	 
} 
 
//读1个字节，ack=1时，发送ACK，ack=0，发送nACK   
unsigned char amg_iic_read_byte(void)
{
	unsigned char i,receive=0;
	amg8833_pin_change_direction(amg8833.sda,amg8833_IN);
	amg8833_pin_change_value(amg8833.sda,1);;
	udelay(4);
	for(i=0;i<8;i++ )
	{
		receive<<=1;
		amg8833_pin_change_value(amg8833.sck,0); 
		udelay(AMG8833_DELAY_TIME);
	    amg8833_pin_change_value(amg8833.sck,1);
		udelay(AMG8833_DELAY_TIME);
		if(amg8833_pin_get_value(amg8833.sda))
			receive |= 0x01;   
	    udelay(AMG8833_DELAY_TIME); 
	}	
    amg8833_pin_change_value(amg8833.sck,0);	
	return receive;
}
//IIC写一个字节数据
unsigned char amg_iic_write_1_byte(unsigned char SlaveAddress, unsigned char REG_Address,unsigned char REG_data)
{
	amg_iic_start();
	amg_iic_send_byte(SlaveAddress);
	if(amg_iic_wait_ack())
	{
		amg_iic_stop();//释放总线
		return 1;//没应答则退出
	}
	amg_iic_send_byte(REG_Address);
	amg_iic_wait_ack();	
	udelay(5);
	amg_iic_send_byte(REG_data);
	amg_iic_wait_ack();	
	amg_iic_stop();
	return 0;
}
 
//IIC读一个字节数据
unsigned char amg_iic_read_1_byte(unsigned char SlaveAddress, unsigned char REG_Address,unsigned char *REG_data) 
{
	amg_iic_start();
	amg_iic_send_byte(SlaveAddress);//发写命令
	if(amg_iic_wait_ack())
	{
		 amg_iic_stop();//释放总线
		 return 1;//没应答则退出
	}		
	amg_iic_send_byte(REG_Address);
	amg_iic_wait_ack();
	udelay(5);
	amg_iic_start(); 
	amg_iic_send_byte(SlaveAddress|0x01);//发读命令
	amg_iic_wait_ack();
	*REG_data = amg_iic_read_byte();
	amg_iic_stop();
	return 0;
}

//I2C读多个字节数据
unsigned char amg_iic_read_n_byte(unsigned char SlaveAddress, unsigned char REG_Address, unsigned char *buf, uint16_t len)
{
	amg_iic_start();
	amg_iic_send_byte(SlaveAddress);//发写命令
	if(amg_iic_wait_ack()) 
	{
		amg_iic_stop();//释放总线
		return 1;//没应答则退出
	}
	amg_iic_send_byte(REG_Address);
	amg_iic_wait_ack();
	udelay(5);
	amg_iic_start(); 
	amg_iic_send_byte(SlaveAddress|0x01);//发读命令
	amg_iic_wait_ack();
	while(len)
	{
		*buf = amg_iic_read_byte();
		if(1 == len)
		{
			amg_iic_nack();
		}
		else
		{
			amg_iic_ack();
		}
		buf++;
		len--;
	}
	amg_iic_stop();
	return 0;
}
 
//I2C写多个字节数据
unsigned char amg_iic_write_n_byte(unsigned char SlaveAddress, unsigned char REG_Address, unsigned char *buf, uint16_t len)
{
	amg_iic_start();
	amg_iic_send_byte(SlaveAddress);//发写命令
	if(amg_iic_wait_ack()) 
	{
		amg_iic_stop();//释放总线
		return 1;//没应答则退出
	}
	amg_iic_send_byte(REG_Address);
	amg_iic_wait_ack();
	while(len--)
	{
		amg_iic_send_byte(*buf++);
		amg_iic_wait_ack();
	}
	amg_iic_stop();
	return 0;
}

/**
 * @description: 打开操作
 * @param {inode} *inode
 * @param {file} *file
 * @return {*}
 * @author: YURI
 */
static int amg8833_drv_open(struct inode *inode, struct file *file)
{
	amg8833_pin_change_value(amg8833.ad0,0);
    //enter normal mode
    amg_iic_write_1_byte(AMG88xx_ADR,AMG88xx_PCTL,AMG88xx_NORMAL_MODE);
    //software reset
    amg_iic_write_1_byte(AMG88xx_ADR,AMG88xx_RST,AMG88xx_INITIAL_RESET);
    //set to 10 FPS
    amg_iic_write_1_byte(AMG88xx_ADR,AMG88xx_FPSC,AMG88xx_FPS_10);
    return 0;
}

/**
 * @description: 释放操作
 * @param {inode} *pinode
 * @param {file} *pfile
 * @return {*}
 * @author: YURI
 */
static int amg8833_drv_release(struct inode *pinode , struct file *pfile)
{
    return 0;
}

/**
 * @description: 
 * @param {file} *file
 * @param {char __user} *buf
 * @param {size_t} count
 * @param {loff_t} *ppos
 * @return {*}
 * @author: YURI
 */
static ssize_t amg8833_drv_read(struct file *file,  char __user *buf, size_t count, loff_t *ppos)
{
	uint8_t rawArray[128],i;
    local_irq_disable();
    amg_iic_read_n_byte(AMG88xx_ADR,AMG88xx_PIXEL_OFFSET,rawArray,128);
    local_irq_enable();
    copy_to_user(buf,rawArray, count);
    return count;
}
static int major = (-1); /* 初始化为无效值 */
static struct class *amg8833_drv_class;
static struct file_operations amg8833_drv_fops = {
    .owner   = THIS_MODULE,
    .open    = amg8833_drv_open,
    .release = amg8833_drv_release,
    .read    = amg8833_drv_read,
};



/* 驱动入口函数 */
static int amg8833_drv_init(void)
{
    printk("KERNEL INIT amg8833 \r\n");
    major = register_chrdev(0, "amg8833_drv", &amg8833_drv_fops); // 注册, 告诉内核，返回值major为自动分配的主设备号
    amg8833_drv_class = class_create(THIS_MODULE, "amg8833drv");
    device_create(amg8833_drv_class, NULL, MKDEV(major, 0), NULL, DEVICE_NAME);
    amg8833_ctl_init();

    
    return 0;
}
 
/* 驱动出口函数 */
static void amg8833_drv_exit(void)
{
    unregister_chrdev(major, "amg8833_drv"); /* 卸载驱动程序，告诉内核 */
    device_destroy(amg8833_drv_class, MKDEV(major, 0));
    class_destroy(amg8833_drv_class);
    amg8833_ctl_uninit();
}

module_init(amg8833_drv_init);
module_exit(amg8833_drv_exit);

MODULE_LICENSE("Dual BSD/GPL");

测试代码

/*
 * @Description: 
 * @Autor: YURI
 * @Date: 2022-01-30 18:34:31
 * @LastEditors: YURI
 * @LastEditTime: 2022-01-31 02:35:01
 */
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <stdio.h>
#include <stdlib.h>
#include <unistd.h>
#include "framebuffer.h"
#include "opencv_mat.h"
#define AMG88xx_PIXEL_TEMP_CONVERSION 0.25
using namespace cv;
#define MIN_TEMP   0
#define MAX_TEMP   30

const unsigned short camColors[] = {0x480F,
            0x400F,0x400F,0x400F,0x4010,0x3810,0x3810,0x3810,0x3810,0x3010,0x3010,
            0x3010,0x2810,0x2810,0x2810,0x2810,0x2010,0x2010,0x2010,0x1810,0x1810,
            0x1811,0x1811,0x1011,0x1011,0x1011,0x0811,0x0811,0x0811,0x0011,0x0011,
            0x0011,0x0011,0x0011,0x0031,0x0031,0x0051,0x0072,0x0072,0x0092,0x00B2,
            0x00B2,0x00D2,0x00F2,0x00F2,0x0112,0x0132,0x0152,0x0152,0x0172,0x0192,
            0x0192,0x01B2,0x01D2,0x01F3,0x01F3,0x0213,0x0233,0x0253,0x0253,0x0273,
            0x0293,0x02B3,0x02D3,0x02D3,0x02F3,0x0313,0x0333,0x0333,0x0353,0x0373,
            0x0394,0x03B4,0x03D4,0x03D4,0x03F4,0x0414,0x0434,0x0454,0x0474,0x0474,
            0x0494,0x04B4,0x04D4,0x04F4,0x0514,0x0534,0x0534,0x0554,0x0554,0x0574,
            0x0574,0x0573,0x0573,0x0573,0x0572,0x0572,0x0572,0x0571,0x0591,0x0591,
            0x0590,0x0590,0x058F,0x058F,0x058F,0x058E,0x05AE,0x05AE,0x05AD,0x05AD,
            0x05AD,0x05AC,0x05AC,0x05AB,0x05CB,0x05CB,0x05CA,0x05CA,0x05CA,0x05C9,
            0x05C9,0x05C8,0x05E8,0x05E8,0x05E7,0x05E7,0x05E6,0x05E6,0x05E6,0x05E5,
            0x05E5,0x0604,0x0604,0x0604,0x0603,0x0603,0x0602,0x0602,0x0601,0x0621,
            0x0621,0x0620,0x0620,0x0620,0x0620,0x0E20,0x0E20,0x0E40,0x1640,0x1640,
            0x1E40,0x1E40,0x2640,0x2640,0x2E40,0x2E60,0x3660,0x3660,0x3E60,0x3E60,
            0x3E60,0x4660,0x4660,0x4E60,0x4E80,0x5680,0x5680,0x5E80,0x5E80,0x6680,
            0x6680,0x6E80,0x6EA0,0x76A0,0x76A0,0x7EA0,0x7EA0,0x86A0,0x86A0,0x8EA0,
            0x8EC0,0x96C0,0x96C0,0x9EC0,0x9EC0,0xA6C0,0xAEC0,0xAEC0,0xB6E0,0xB6E0,
            0xBEE0,0xBEE0,0xC6E0,0xC6E0,0xCEE0,0xCEE0,0xD6E0,0xD700,0xDF00,0xDEE0,
            0xDEC0,0xDEA0,0xDE80,0xDE80,0xE660,0xE640,0xE620,0xE600,0xE5E0,0xE5C0,
            0xE5A0,0xE580,0xE560,0xE540,0xE520,0xE500,0xE4E0,0xE4C0,0xE4A0,0xE480,
            0xE460,0xEC40,0xEC20,0xEC00,0xEBE0,0xEBC0,0xEBA0,0xEB80,0xEB60,0xEB40,
            0xEB20,0xEB00,0xEAE0,0xEAC0,0xEAA0,0xEA80,0xEA60,0xEA40,0xF220,0xF200,
            0xF1E0,0xF1C0,0xF1A0,0xF180,0xF160,0xF140,0xF100,0xF0E0,0xF0C0,0xF0A0,
            0xF080,0xF060,0xF040,0xF020,0xF800};

short signed_To_unsigned(short val)
{
	short absVal = (val & 0x7FF);
	return (val & 0x800) ? 0 - absVal : absVal ;
}
opencv_mat*           mat_convert; 
framebuffer *fb;
#define RGB565_RED      0xf800
#define RGB565_GREEN    0x07e0
#define RGB565_BLUE     0x001f
int main(int argc,void **argv)
{
    int fd,i;
    Mat image,show;
    char* filename=NULL;
    unsigned char buf[128];
	unsigned char rgbbuf[8*8*3];
	int color_index=0;
    short data[64];
	short recast;
	short converted;
	fb=new framebuffer("/dev/fb0");
    filename = (char*)argv[1];
    fd = open(filename, O_RDWR);//打开dev/firstdrv设备文件
    mat_convert=new opencv_mat(8,8);
    if (fd < 0)//小于0说明没有成功
    {
        printf("error, can't open %s\n", filename);
        return 0;
    }
    while (1)
    {
        read(fd,buf,128);
        for(i=0; i<64; i++)
	    {
            unsigned char pos = i *2;
            recast = ((short)buf[pos + 1] << 8) | ((short)buf[pos]);        
            converted = signed_To_unsigned(recast) * AMG88xx_PIXEL_TEMP_CONVERSION;
            data[i] = converted;
	    }    
        for(int j=0;j<8;j++){
            for(int k=0;k<8;k++)
            {
				color_index= (data[8*j+k]-MIN_TEMP) *( 255/(MAX_TEMP-MIN_TEMP));
                if(color_index<0){
				    rgbbuf[8*3*j+3*k]=0;
                    rgbbuf[8*3*j+3*k+1]=0;
                    rgbbuf[8*3*j+3*k+2]=0;
                }else if(color_index>255){
                    rgbbuf[8*3*j+3*k]=0xFF;
                    rgbbuf[8*3*j+3*k+1]=0xFF;
                    rgbbuf[8*3*j+3*k+2]=0xFF;
                }else{
                    rgbbuf[8*3*j+3*k+2]=(camColors[color_index]&RGB565_BLUE)<<3;
                    rgbbuf[8*3*j+3*k+1]=(camColors[color_index]&RGB565_GREEN)>>3;
                    rgbbuf[8*3*j+3*k]=(camColors[color_index]&RGB565_RED)>>8;
                }
                
            }     
        }
        image=mat_convert->opencv_convert(rgbbuf);
        resize(image,show,Size(0,0),200,130);
		fb->show_rgbbuffer(show.data,0,0,show.cols,show.rows);
    }
    close(fd);
}

这里我偷懒了没有自己写插值算法，而是直接使用的OpenCV的插值函数，所以如果要用，还需要移植OpenCV。

具体代码参考
git@github.com:Yueyang123/arm_media.git

最终效果

今天是除夕夜，大家过年好。

版权声明：本文为CSDN博主「与光同程」的原创文章，遵循CC 4.0 BY-SA版权协议，转载请附上原文出处链接及本声明。
原文链接：https://blog.csdn.net/yy197696/article/details/122761228