首页 » STM32 » 正文
STM32

C51蓝牙串口&循迹小车代码实现

/***********************头文件**************************/
#include <regx52.h>



/************************位声明*************************/
/*红外信号位*/
sbit Inf_Headr	 = P0^5;
sbit Inf_Right_1 = P0^4;
sbit Inf_Right_2 = P0^3;
sbit Inf_Center  = P0^2;
sbit Inf_Left_1  = P0^1;
sbit Inf_Left_2  = P0^0;
/*寻路舵机*/
sbit Motor = P3^5;
/*测距模块信号源*/
sbit Trig  = P2^1;
sbit Echo  = P2^2;
/*µ电机驱动模块*/
sbit EN_Right  = P1^5;
sbit EN_Left   = P1^0;
sbit in_Right1 = P1^4;
sbit in_Right2 = P1^3;
sbit in_Left1  = P1^2;
sbit in_Left2  = P1^1;
/*LED*/
sbit LED       = P2^0;

/***********蓝牙模块串口*********/
void HC_06_Init();		                   		//串口初始化
void HC_06_SendData(unsigned char Data);		//发送
void HC_06_Interrupt();							//串口中断


/*************************************/
/***********Pwm调速**********/
void Turn_Right(unsigned char pwm);					//右转
void Turn_Left(unsigned char pwm);					//左转
void Go_Forword(unsigned char speed);				//前进
void Go_Back(unsigned char speed);					//后退
void Stop();										//停
void Timer0_PWM_init();								//PWM
void Timer0_Interrupt();							//


/**************************************/
/**************舵机偏转角度*************/
void Mot_Angle(unsigned char _angle);
/***************************************/
/**************LED**************/
void Control_LED(unsigned char led_switch);
/*************红外寻迹模式***************/
void Inf_mode();
/***************************************/
/*****************变量声明**************/
unsigned char PWM=10;
unsigned char pwm_count;			//PWM计时
unsigned char motor_count;			//舵机计时
unsigned char angle;
bit mode;
/*************************/

/********************************************************/
/*************************主程序*************************/
/********************************************************/

void main()
{

	//初始化
	HC_06_Init();
	Timer0_PWM_init();
	
	while(1)		//主循环判断红外状态
	{
		if(mode==1)
			Inf_mode();

	}
	
}


//函数定义

//蓝牙串口init
void HC_06_Init()
{
	PCON |= 0x80;
	SCON = 0x50;
	TMOD &= 0x0F;
	TMOD |= 0x20;
	TL1 = 0xFA;
	TH1 = 0xFA;
	ET1 = 0;
	TR1 = 1;
	
	ES=1;
	EA=1;
}

//发送
void HC_06_SendData(unsigned char Data)
{
	TI=1;
	SBUF=Data;
	while(TI==0);
	TI=0;
	
}

//接收---控制
void HC_06_Interrupt() interrupt 4
{
	if(RI==1)
	{

		if(SBUF==0x41)
			Go_Forword(PWM);	//前进
		else if(SBUF==0x42)
			Turn_Left(PWM);		//左转
		else if(SBUF==0x43)
			Stop();						//停
		else if(SBUF==0x44)
			Turn_Right(PWM);	//右转
		else if(SBUF==0x45)
			Go_Back(PWM);			//后退
		else if(SBUF==0x76)
			Control_LED(0);		//LED开
		else if(SBUF==0x2d)
		{
			PWM-=5;						//减速
			HC_06_SendData(PWM);
		}
		else if(SBUF==0x2b)
		{
			PWM+=5;						//加速
			HC_06_SendData(PWM);
		}
		else if(SBUF==0x51)	//红外模式
			mode=1;	
		else if(SBUF==0x57)	//蓝牙模式
			mode=0;	
		
		
		RI=0;
	}
}


void Turn_Right(unsigned char pwm)
{
	PWM=pwm;
	
	in_Right1=1;
	in_Right2=0;
	
	in_Left1=1;
	in_Left2=0;
}



void Turn_Left(unsigned char pwm)
{
	PWM=pwm;
	
	in_Right1=0;
	in_Right2=1;
	
	in_Left1=0;
	in_Left2=1;
	
}


void Go_Forword(unsigned char speed)
{
	PWM=speed;
	
	in_Right1=0;
	in_Right2=1;
	
	in_Left1=1;
	in_Left2=0;
	
}


void Go_Back(unsigned char speed)
{
	PWM=speed;
	
	in_Right1=1;
	in_Right2=0;
	
	in_Left1=0;
	in_Left2=1;
	
}


void Stop()
{
	in_Left1=0;
	in_Left2=0;
	
	in_Right1=0;
	in_Right2=0;
}



void Timer0_PWM_init()
{

	TMOD &= 0xF0;
	TL0 = 0xF5;
	TH0 = 0xF5;
	TF0 = 0;
	TR0 = 1;

	ET0=1;
	EA=1;
	PT0=0;
	
}


void Timer0_Interrupt() interrupt 1
{
	TL0 = 0xF5;
	TH0 = 0xF5;
	pwm_count++;
	if(pwm_count<PWM)
	{
		EN_Right=1;
		EN_Left=1;
	}
	else
	{
		EN_Right=0;
		EN_Left=0;
	}

	//
	if(pwm_count>=100)
		pwm_count=0;
		
}



void Mot_Angle(unsigned char _angle)
{
	angle=_angle;
}


void Control_LED(unsigned char led_switch)
{
	switch(led_switch)
	{
		case 0:
			LED=0;
		case 1:
			LED=1;
	}
}




void Inf_mode()
{

		if(Inf_Center==1&&Inf_Right_1==0&&Inf_Right_2==0&& Inf_Left_1==0&&Inf_Left_2==0)
			Go_Forword(16);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==0)
			Go_Forword(14);
		
		else if(Inf_Center==1&& Inf_Right_1==1&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(30);
		else if(Inf_Center==1&& Inf_Right_1==1&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		
		else if(Inf_Center==0&& Inf_Right_1==1&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(30);
		else if(Inf_Center==0&& Inf_Right_1==1&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		
		
		
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==0)
			Turn_Left(30);
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==1)
			Turn_Left(35);
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==1)
			Turn_Left(35);
		
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==0)
			Turn_Left(30);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==1)
			Turn_Left(35);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==1)
			Turn_Left(35);
	
		else if(Inf_Center==1&& Inf_Right_1==1&&Inf_Right_2==1&&Inf_Left_1==1&&Inf_Left_2==1)
			Stop();
		
		if(Inf_Headr==0)
		{
			Turn_Left(35);
		}
}

版权声明：本文为CSDN博主「KCJ.」的原创文章，遵循CC 4.0 BY-SA版权协议，转载请附上原文出处链接及本声明。
原文链接：https://blog.csdn.net/qq_60478726/article/details/122608292 

/***********************头文件**************************/
#include <regx52.h>



/************************位声明*************************/
/*红外信号位*/
sbit Inf_Headr	 = P0^5;
sbit Inf_Right_1 = P0^4;
sbit Inf_Right_2 = P0^3;
sbit Inf_Center  = P0^2;
sbit Inf_Left_1  = P0^1;
sbit Inf_Left_2  = P0^0;
/*寻路舵机*/
sbit Motor = P3^5;
/*测距模块信号源*/
sbit Trig  = P2^1;
sbit Echo  = P2^2;
/*µ电机驱动模块*/
sbit EN_Right  = P1^5;
sbit EN_Left   = P1^0;
sbit in_Right1 = P1^4;
sbit in_Right2 = P1^3;
sbit in_Left1  = P1^2;
sbit in_Left2  = P1^1;
/*LED*/
sbit LED       = P2^0;

/***********蓝牙模块串口*********/
void HC_06_Init();		                   		//串口初始化
void HC_06_SendData(unsigned char Data);		//发送
void HC_06_Interrupt();							//串口中断


/*************************************/
/***********Pwm调速**********/
void Turn_Right(unsigned char pwm);					//右转
void Turn_Left(unsigned char pwm);					//左转
void Go_Forword(unsigned char speed);				//前进
void Go_Back(unsigned char speed);					//后退
void Stop();										//停
void Timer0_PWM_init();								//PWM
void Timer0_Interrupt();							//


/**************************************/
/**************舵机偏转角度*************/
void Mot_Angle(unsigned char _angle);
/***************************************/
/**************LED**************/
void Control_LED(unsigned char led_switch);
/*************红外寻迹模式***************/
void Inf_mode();
/***************************************/
/*****************变量声明**************/
unsigned char PWM=10;
unsigned char pwm_count;			//PWM计时
unsigned char motor_count;			//舵机计时
unsigned char angle;
bit mode;
/*************************/

/********************************************************/
/*************************主程序*************************/
/********************************************************/

void main()
{

	//初始化
	HC_06_Init();
	Timer0_PWM_init();
	
	while(1)		//主循环判断红外状态
	{
		if(mode==1)
			Inf_mode();

	}
	
}


//函数定义

//蓝牙串口init
void HC_06_Init()
{
	PCON |= 0x80;
	SCON = 0x50;
	TMOD &= 0x0F;
	TMOD |= 0x20;
	TL1 = 0xFA;
	TH1 = 0xFA;
	ET1 = 0;
	TR1 = 1;
	
	ES=1;
	EA=1;
}

//发送
void HC_06_SendData(unsigned char Data)
{
	TI=1;
	SBUF=Data;
	while(TI==0);
	TI=0;
	
}

//接收---控制
void HC_06_Interrupt() interrupt 4
{
	if(RI==1)
	{

		if(SBUF==0x41)
			Go_Forword(PWM);	//前进
		else if(SBUF==0x42)
			Turn_Left(PWM);		//左转
		else if(SBUF==0x43)
			Stop();						//停
		else if(SBUF==0x44)
			Turn_Right(PWM);	//右转
		else if(SBUF==0x45)
			Go_Back(PWM);			//后退
		else if(SBUF==0x76)
			Control_LED(0);		//LED开
		else if(SBUF==0x2d)
		{
			PWM-=5;						//减速
			HC_06_SendData(PWM);
		}
		else if(SBUF==0x2b)
		{
			PWM+=5;						//加速
			HC_06_SendData(PWM);
		}
		else if(SBUF==0x51)	//红外模式
			mode=1;	
		else if(SBUF==0x57)	//蓝牙模式
			mode=0;	
		
		
		RI=0;
	}
}


void Turn_Right(unsigned char pwm)
{
	PWM=pwm;
	
	in_Right1=1;
	in_Right2=0;
	
	in_Left1=1;
	in_Left2=0;
}



void Turn_Left(unsigned char pwm)
{
	PWM=pwm;
	
	in_Right1=0;
	in_Right2=1;
	
	in_Left1=0;
	in_Left2=1;
	
}


void Go_Forword(unsigned char speed)
{
	PWM=speed;
	
	in_Right1=0;
	in_Right2=1;
	
	in_Left1=1;
	in_Left2=0;
	
}


void Go_Back(unsigned char speed)
{
	PWM=speed;
	
	in_Right1=1;
	in_Right2=0;
	
	in_Left1=0;
	in_Left2=1;
	
}


void Stop()
{
	in_Left1=0;
	in_Left2=0;
	
	in_Right1=0;
	in_Right2=0;
}



void Timer0_PWM_init()
{

	TMOD &= 0xF0;
	TL0 = 0xF5;
	TH0 = 0xF5;
	TF0 = 0;
	TR0 = 1;

	ET0=1;
	EA=1;
	PT0=0;
	
}


void Timer0_Interrupt() interrupt 1
{
	TL0 = 0xF5;
	TH0 = 0xF5;
	pwm_count++;
	if(pwm_count<PWM)
	{
		EN_Right=1;
		EN_Left=1;
	}
	else
	{
		EN_Right=0;
		EN_Left=0;
	}

	//
	if(pwm_count>=100)
		pwm_count=0;
		
}



void Mot_Angle(unsigned char _angle)
{
	angle=_angle;
}


void Control_LED(unsigned char led_switch)
{
	switch(led_switch)
	{
		case 0:
			LED=0;
		case 1:
			LED=1;
	}
}




void Inf_mode()
{

		if(Inf_Center==1&&Inf_Right_1==0&&Inf_Right_2==0&& Inf_Left_1==0&&Inf_Left_2==0)
			Go_Forword(16);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==0)
			Go_Forword(14);
		
		else if(Inf_Center==1&& Inf_Right_1==1&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(30);
		else if(Inf_Center==1&& Inf_Right_1==1&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		
		else if(Inf_Center==0&& Inf_Right_1==1&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(30);
		else if(Inf_Center==0&& Inf_Right_1==1&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==1&&Inf_Left_1==0&&Inf_Left_2==0)
			Turn_Right(35);
		
		
		
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==0)
			Turn_Left(30);
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==1)
			Turn_Left(35);
		else if(Inf_Center==1&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==1)
			Turn_Left(35);
		
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==0)
			Turn_Left(30);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==0&&Inf_Left_2==1)
			Turn_Left(35);
		else if(Inf_Center==0&& Inf_Right_1==0&&Inf_Right_2==0&&Inf_Left_1==1&&Inf_Left_2==1)
			Turn_Left(35);
	
		else if(Inf_Center==1&& Inf_Right_1==1&&Inf_Right_2==1&&Inf_Left_1==1&&Inf_Left_2==1)
			Stop();
		
		if(Inf_Headr==0)
		{
			Turn_Left(35);
		}
}

版权声明：本文为CSDN博主「KCJ.」的原创文章，遵循CC 4.0 BY-SA版权协议，转载请附上原文出处链接及本声明。
原文链接：https://blog.csdn.net/qq_60478726/article/details/122608292

标签： ·
生成海报
点击下载海报
加载中
点赞 0

KCJ.

我还没有学会写个人说明！

暂无评论

发表评论

相关推荐

74HC138译码器的原理和使用
单片机 2024-12-19

74HC138译码器的原理和使用

前言 译码器就是将每个输入的二进制代码译成对应的输出高低电平信号，和编码器互为逆过程。 百度百科 74HC138是一款高速CMOS器件，74HC138引脚兼容低功耗肖特基TTL（LSTTL&#xf

分享到：